Shelly Wave - Firmware updates

Shelly Wave 1

• EU - ver. 14.00
• US - ver. 14.00
• ANZ - ver. 14.00

- Added Detached mode

- Fixed OTA signalization

- Fixed Binary report with normally closed

- Fixed push button inclusion / exclusion

- other minor fixes

ver. [10.13] - [2023-06-01]

- initial firmware release

Shelly Wave 1PM

• EU - ver. 14.01
• US - ver. 14.01
• ANZ - ver. 14.01

- Added Detached mode

- Added Energy reporting precision 0,01 kWh

- Fixed device not working properly connected DC

- Fixed OTA signalization

- Fixed Binary report with normally closed

- Fixed random power cycle (SDK issue)

- Removed parameters 91 - 94

- Removed Inclusion / exclusion output signalization

- other minor improvements and fixes

- Removed delay from input detection to output response.
- Fix Binary Switch report after auto off 
- Power measurement optimised for 'true power' measurement

- Added filter for electrical disturbances to avoid unnecessary reporting.
- Circuit protection system (over current, overheat) detection improved
- Improved power measurement system
- Corrected configuration Command Class reports for non-existent parameters
- Parameter 120 "factory reset" characteristics changed to size = 1 Byte.
- other minor fixes and improvements.

ver. [10.13] - [2023-06-01]

- initial firmware release

Shelly Wave 2PM

• EU - ver. 16.05
• US - ver. 16.05
• ANZ - ver. 16.05

ver. [16.05] - [2025-01-16]

- Fix Multichannel Association on EP 2

ver. [16.04] - [2025-11-27]

- Fix detached mode SW2

- External switches exclusion disabled

ver. [16.02] - [2025-10-07]

- SDK with fixed dead node issue

- Added detached mode and kWh precision set to 2 decimal points

- Added parameter 117 (reboot parameter)
- Added root control and reports of endpoints

- Watt reports when NO/NC parameter is active

- Fix switch binary report when powered with DC

- Fix Endpoint 2 report state change on single channel association

- Fix supervision report for root command
- Fix Meter reports, Associations and Binary Switch

- Removed parameters no. 91 - 94 from the FW

- Improved over-current and over-voltage protection

- Other minor improvements

ver. [10.35] - [2024-03-28]

ver. [10.30] - [2024-01-08]

ver. [10.27] - [2023-06-05]

- initial firmware release

Shelly Wave Shutter

• EU - ver. 14.02
• US - ver. 14.02
• ANZ - ver. 14.02

ver. [14.02] - [2025-11-28]

- SDK with fixed dead node issue

- Fixed single-channel supervision report

- Fixed sometimes the device reports odd power value

- Added detached mode & parameters 7 and 8

- Added parameter 118; Enable SW exclusion

- other minor improvements

ver. [12.23] - [2024-06-14]

- fixed parameter system to support the new Z-Wave system

ver. [12.21] - [2024-04-17]

- fixed switch input and output orientation

- fixed remote commands compatibility

- other minor improvements

ver. [12.17] - [2023-11-10]

- Improved no line alarm detection

- filter on power spike reporting

- two minor improvements

ver. [12.13] - [2023-09-04]

- initial firmware release

Shelly Plug UK

• EU - ver. 10.05

ver. [10.05] - [2024-02-06]

- Fixed very low power reports

- Improved voltage resolution

- Meter report is now in mA (precision 3)

- Added Association for Multilevel-Switch

- other minor Fixes & Improvements

ver. [10.00] - [2023-08-24]

initial firmware release

Shelly Plug US

• US - ver. 10.11

ver. [10.11] - [2024-03-18]

- optimised temperature conversion table

- Meter Reset Command fixed

- other minor improvements

ver. [10.08] - [2023-08-19]

initial firmware release

Shelly Plug S

• EU - ver. 12.02

ver. [12.02] - [2026-02-05]

- SDK with fixed dead node issue

- fixed AC disconnect alarm functionality

- improved Zero Crossing detection

Shelly Wave i4

• EU - ver. 13.01
• US - ver. 13.01
• ANZ - ver. 13.01

ver. [13.01] - [2026-03-12]

- SDK with fixed dead node issue

- Fixed Association

- Fixed Part number

- Fixed Indicator CC support

- Fixed short press for Central Scene manager (200ms -> 500ms)

- Added Parameter 118 (switch exclusion enable/disable)

- Added Parameter 117 - Reboot device

- other minor fixes and improvements

ver. [11.05] - [2024-05-17]

- Binary switch report at boot up
- Parameters 1 - 4 value 1 fixed
- optimised temperature conversion table

ver. [11.03] - [2024-03-28] 

- Binary Switch support

- fixed OTA led signalisation

- other minor fixes and improvements

 
ver. [10.06] - [2023-09-27]

initial firmware release

Shelly Wave i4 DC

• EU - ver. 13.00
• US - ver. 13.00
• ANZ - ver. 13.00

ver. [13.00] - [2026-03-11]

- Fixed Association

- Fixed Part number

- Fixed Indicator CC support

- Fixed short press for Central Scene manager (200ms -> 500ms)

- Added Parameter 117 - Reboot device

- other minor fixes and improvements

ver. [11.05] - [2024-05-17]

- Binary switch report at boot up
- Parameters 1 - 4 value 1 fixed

ver. [11.04] - [2024-04-26] 

- optimised temperature conversion table

ver. [11.03] - [2024-03-28] 

- Binary Switch support 

- fixed OTA led signalisation

- other minor fixes and improvements

ver. [10.06] - [2023-09-27]

initial firmware release

Shelly Wave Pro 1

• EU - ver. 13.01
• US - ver. 13.01
• ANZ - Ver. 13.01

Ver. [13.01] - [2026-02-17]

- SDK with fixed dead node issue

- Fixed soft reset from input toggles

- Fixed sw2 detached mode parameter default -> 1 (active)

- Removed parameters 36/39

- Removed parameters no. 91, 92, 93, 94

- Removed Inclusion/exclusion" indication (2x ON/OFF output)

- other minor improvements

ver. [11.01] - [2024-03-18]

- optimized temperature conversion table

- other minor improvements

ver. [10.11] - [2023-11-15]

- initial firmware release

Shelly Wave Pro 2

• EU - ver. 12.00
• US - ver. 12.00
• ANZ - ver. 12.00

ver. [12.00] - [2026-02-27]

- SDK with fixed dead node issue

- Fixed Binary Switch reporting in association with NO/NC

- Added Detached mode

- Added Parameter 117 for device rebooting

- Removed Parameters 91, 92, 93, 94

- Removed Inclusion/exclusion indication (2x ON/OFF output)

- optimized temperature conversion table

- other minor improvements

ver. [10.06] - [2023-10-13]

Shelly Wave Pro 1PM

• EU - ver. 13.01
• US - ver. 13.01
• ANZ - ver. 13.01

Ver. [13.01] - [2026-02-17]

- SDK with fixed dead node issue

- Fixed Overvoltage

- Fixed Overcurrent

- Fixed soft reset from input toggles

- Fixed sw2 detached mode parameter default -> 1 (active)

- Removed parameters no. 91, 92, 93, 94

- Removed Inclusion/exclusion indication (2x ON/OFF output)

- Changed energy reporting to two decimal points

- other minor improvements

ver. [11.03] - [2024-03-25]

- minor improvements

ver. [11.01] - [2024-03-25]

- optimized temperature conversion table

- other minor improvements

ver. [10.12] - [2023-11-24]

Shelly Wave Pro 2PM

• EU - ver. 13.04
• US - ver. 13.04
• ANZ - ver. 13.04

Ver. [13.04] - [2026-03-09]

- SDK with fixed dead node issue

- Fixed overcurrent alarm threshold

- Fixed Meter CC on endpoints

- Fixed respond to Import rate type Meter get command

- Fixed Binary Switch Reporting in association with Normally Open / Normally Closed(NO/NC)

- Added Parameter 117 for device rebooting

- Changed Energy reporting to 2 decimal points

- Removed AC main disconnected alarm

- Removed PARs 91, 92, 93, 94

- Removed Inclusion/exclusion indication (2x ON/OFF output)

- other minor improvements

- optimized temperature conversion table

- other minor improvements

ver. [10.07] - [2023-11-23]

Shelly Wave Pro Shutter

• EU - ver. 12.03
• US - ver. 12.03
• ANZ - ver. 12.03

Ver. [12.03] - [2026-04-01]

- SDK with fixed dead node issue

- Added detached mode

- Added inclusion option with disabled input parameter

- Added parameter state reporting to controller

- Added Meter CC support to endpoints

- Fixed associations to resolve Home Assistant issues

- Fixed LED signaling

- Fixed Meter OP parameter (disables end switches when set to 10)

- Fixed Meter CC (no watt reporting when parameter 36 is set to 0)

- Fixed venetian mode

- Fixed parameter 39

- Fixed calibration issue

- Fixed abnormal output when parameter 85 is set to 0

- Fixed multilevel report & multilevel switch start/stop behavior

- other minor improvements

ver. [10.08] - [2024-03-20]

- optimized temperature conversion table

- fixed Power Up Shutter Position Report

- fixed unsolicited Power Report

- OTA in progress signalization

- other minor improvements

ver. [10.00] - [2024-01-08]

- initial firmware release

Shelly Wave 1 Mini

• EU - ver. 14.00
• US - ver. 14.00
• ANZ - ver. 14.00

ver. [14.00] - [2024-04-04]

ver. [10.04] - [2024-04-04]

- optimized temperature conversion table

- other minor improvements

ver. [10.02] - [2023-06-26]

initial firmware release

Shelly Wave 1PM Mini

• EU - ver. 14.03
• US - ver. 14.03
• ANZ - ver. 14.03

ver. [14.03] - [2026-02-19]

- SDK with fixed dead node issue

- Fixed overvoltage threshold

- Fixed rapid relay switching when parameter 23 is set to 1

- Fixed Auto ON/OFF parameter timer. Timer resets at command ON/OFF even if the state doesn't change.

- Fixed default values for Par 36 & 39

- Fixed meter unsolicited reports

- Fixed binary switch unsolicited reports and Basic set

- Fixed overcurrent alarm

- Fixed switch binary report with normally closed

- Fixed Fix random 0W reports

- Fixed 60Hz power supply functionality

- Added detached mode

- Added Watt report at boot up

- Added Parameter 117; Remote Reboot

- Added kWh precision, 2 decimals

- Improved Overvoltage alarm

- Removed Alarm parameters 91, 92, 93, 94 and associated code

- Removed Outputs blink on successful inclusion/exclusion

- Removed Multilevel Switch Support

- other minor fixes and improvements

ver. [11.03] - [2024-03-29]

- optimized temperature conversion table

- other minor improvements

ver. [11.01] - [2023-06-26]

initial firmware release

Shelly Wave PM Mini

• EU - ver. 13.01
• US - ver. 13.01
• ANZ - ver. 13.01

ver. [13.01] - [2025-09-11]

- SDK with fixed dead node issue

- Fixed Power measurement spams on capacitive loads

ver. [12.00] - [2025-05-20]

- kWh precision set to 2 decimal points

- Fix random 0W reports

- Fix OTA color signalization

- other minor improvements

ver. [10.06] - [2024-03-28]

- optimized temperature conversion table

- other minor improvements

ver. [10.03] - [2023-11-27]

initial firmware release

Shelly Wave Pro 3

• EU - ver. 13.02
• US - ver. 13.02
• ANZ - ver. 13.02

ver. [13.02] - [2025-11-25]

- SDK with fixed dead node issue

- Added parameters for detached mode

- Added parameter 118 Enable SW exclusion

- other minor improvements

ver. [11.00] - [2025-05-23]

- Fixed associations

- Fixed power cycle through inputs

- Removed output indicator for successful inclusion/exclusion

- Removed parameters 91, 92, 93, 94

- other minor improvements

ver. [10.07] - [2024-07-03]

- Fixed binary switch on root reporting of all endpoints

ver. [10.06] - [2024-05-16]

initial firmware release

Shelly Wave Dimmer

• EU - ver. 12.03
• US - ver. 12.03
• ANZ - ver. 12.03

ver. [12.03] - [2025-12-19]

- SDK with fixed dead node issue

- Fix Associations not working properly

- Fix Parameter 123 min dimming value

- Fix Meter CC missing on endpoint 1

- Fix double click not working according to specifications

- other minor improvements

ver. [11.10] - [2025-10-29]

- Fix Detached mode Binary Switch when SW set to toggle

- Improved Mosfet PWM

- other minor fixes and improvements

ver. [11.07] - [2025-05-19]

- initial firmware release

Shelly Wave Pro Dimmer 1PM

• EU - ver. 12.06
• US - ver. 12.06
• ANZ - ver. 12.06

ver. [12.06] - [2026-02-09]

- SDK with fixed dead node issue

- Fixed Inclusion over inputs

- Fixed Associations

- Fixed Soft reset loop

- other minor fixes and improvements

ver. [10.10] - [2024-10-04]

initial firmware release

Shelly Wave Pro Dimmer 2PM

• EU - ver. 12.07
• US - ver. 12.07 
• ANZ - ver. 12.07 

ver [12.07] - [2026-02-10]

- Fixed Frequency error at final test

ver. [12.06] - [2026-02-09]

- SDK with fixed dead node issue

- Fixed Inclusion over inputs

- Fixed part number

- Fixed Associations not working properly

- Fixed Meter CC

- Fixed last on value

- Fixed avoid switch ON after SmartStart

- Fixed switch multilevel root

- Fixed auto off timer not working

- Improved calibration range

- other minor fixes and improvements

ver. [10.02] - [2024-10-24]

initial firmware release

Shelly Wave Door/Window

• EU - ver. 11.09
• US - ver. 11.09 
• ANZ - ver. 11.09 

ver. [11.09] - [2025-10-03]

- Fixed No communication after inclusion state change

- Changed parameter 157 value

- Improved Angle measuring

- other fixes and improvements

ver. [11.07] - [2025-09-17]

- Added EU LR support

- Fixed inclination reports

ver. [10.17] - [2024-10-15]

initial firmware release

Shelly Wave Motion

• EU - ver. 11.10
• US - ver. 11.10 
• ANZ - ver. 11.10 

ver. [11.10] - [2025-12-04]

- Fixed OTA by adding sign and encryption keys

- Fixed PIR sensor config

- Fixed Wake Up Interval ignored

- Fixed multilevel sensor read value to endpoint

- Fixed Wakeup intervals

- Added EU LR support

- Changed size of 159 parameter

- Changed sensitivity values of pir sensor

- Improved handle edge cases for wakeup CC

ver. [10.00] - [2025-04-03]

initial firmware release

Shelly Wave H&T